Carpenter Tools Names in English with their Pictures

• Hammer
• Saw
• Chisel
• Mallet
• Plane
• Level
• Tape
• Square
• Ruler
• Clamp
• Screwdriver
• Drill
• Bit
• Nailset
• File
• Rasps
• Awl
• Wrench
• Pliers
• Crowbar

Carpenter Tools Names in English and Pictures

• Hammer
  A tool used to drive nails into wood or remove them with the back claw.
  
• Saw
  A sharp-edged tool used to cut wood into pieces by hand or with power.
  
• Chisel
  A metal tool with a sharp edge used to shape or carve wood by removing small parts.
  
• Mallet
  A soft-headed hammer used with chisels to shape wood without damaging it.
  
• Plane
  A tool used to smooth or level wooden surfaces by shaving off thin layers.
  
• Level
  A straight tool with a liquid bubble inside used to check if a surface is perfectly horizontal or vertical.
  
• Tape
  A flexible measuring tool (usually called measuring tape) used to measure lengths.
  
• Square
  A tool with a right angle used to check or mark 90-degree angles in woodwork.
  
• Ruler
  A straight measuring tool used for short and precise measurements on wood.
  
• Clamp
  A tool used to tightly hold two pieces of wood together while gluing or cutting.
  
• Screwdriver
  A tool used to tighten or loosen screws by turning them.
  
• Drill
  A power or hand tool used to make holes in wood for screws or dowels.
  
• Bit
  The cutting part that attaches to the drill and comes in different shapes and sizes.
  
• Nailset
  A small pointed tool used to push nail heads just below the wood surface for a smooth finish.
  
• File
  A metal tool with rough edges used to smooth or shape wood or metal edges.
  
• Rasps
  A coarse tool similar to a file, used to remove rough wood quickly.
  
• Awl
  A pointed hand tool used to mark wood or start a small hole for drilling or nailing.
  
• Wrench
  A tool used to tighten or loosen nuts and bolts in furniture or wood frames.
  
• Pliers
  A gripping tool used to hold, bend, or pull small nails and wires.
  
• Crowbar
  A strong metal bar used to pull apart nailed boards or lift heavy objects during dismantling.
  

Carpenter Tools Names in English and Pictures

Basic Carpenter Tools Names in English

• Sandpaper
• Sander
• Workbench
• Vise
• Stud finder
• Marking gauge
• Chalk line
• Handsaw
• Jigsaw
• Circular saw
• Chain saw
• Table saw
• Coping saw
• Bevel gauge
• Nail gun
• Wood glue
• Nailer
• Spirit level
• Framing square
• Try square

Carpenter Tools Names with their Pictures

• Sandpaper
  A rough paper used to smooth wooden surfaces by rubbing.
  
• Sander
  A power tool that quickly smooths large wood areas using sandpaper.
  
• Workbench
  A strong table where carpentry work is done; it holds tools and wood.
  
• Vise
  A tool attached to a workbench that holds wood firmly in place while working.
  
• Stud Finder
  A small device used to locate wooden studs behind walls for safe drilling.
  
• Marking Gauge
  A tool used to draw straight, parallel lines on wood before cutting.
  
• Chalk Line
  A string tool filled with chalk powder used to mark long straight lines on wood.
  
• Handsaw
  A manual saw with a handle, used for cutting wood by hand.
  
• Jigsaw
  A power tool with a small, moving blade that cuts curves and shapes in wood.
  
• Circular Saw
  A power saw with a round blade that makes fast, straight cuts in wood.
  
• Chain Saw
  A tool with a rotating chain blade used for cutting thick wood or tree trunks.
  
• Table Saw
  A large saw fixed to a table, used for straight and accurate wood cutting.
  
• Coping Saw
  A small, thin-bladed saw used for cutting curves and fine shapes in wood.
  
• Bevel Gauge
  A tool used to copy and mark angles for cutting wood at the right angle.
  
• Nail Gun
  A power tool that quickly drives nails into wood, saving time and effort.
  
• Wood Glue
  A strong adhesive used to stick wooden parts together permanently.
  
• Nailer
  A general term for tools (manual or powered) used to insert nails into wood.
  
• Spirit Level
  A tool with a bubble tube used to check if a surface is perfectly level or straight.
  
• Framing Square
  A large L-shaped tool used for marking and checking right angles in framing work.
  
• Try Square
  A smaller square used to check 90-degree corners and edges for accuracy.
  

Basic Carpenter Tools Names in English

Top 40 Hand Tools for Every Woodworker

• Speed square
• Router
• Router bit
• Spokeshave
• Folding rule
• Center punch
• Jack plane
• Claw hammer
• Scribe
• Dovetail saw
• Tenon saw
• Fret saw
• Utility knife
• Dust mask
• Safety goggles
• Ear protectors
• Apron
• Tool belt
• Wood rasp
• Carving knife

List Of Carpenter Tools And Pictures

• Speed Square
  A triangular tool used for marking angles and straight lines quickly on wood.
  
• Router
  A power tool used to hollow out or shape the edges and surfaces of wood.
  
• Router Bit
  The cutting part of a router that comes in different shapes for different wood designs.
  
• Spokeshave
  A hand tool used to shape and smooth curved wooden surfaces, like chair legs.
  
• Folding Rule
  A ruler made of wooden or plastic parts that fold together for easy storage and measuring.
  
• Center Punch
  A pointed tool used to mark a small dent in wood before drilling to keep the drill steady.
  
• Jack Plane
  A medium-sized hand plane used to smooth rough wood and make it flat.
  
• Claw Hammer
  A hammer with a flat side for driving nails and a curved side for pulling them out.
  
• Scribe
  A sharp-pointed tool used to mark fine lines or outlines on wood before cutting.
  
• Dovetail Saw
  A small saw used to make precise and clean cuts for wood joints like dovetails.
  
• Tenon Saw
  A saw with a stiff blade used for straight, controlled cuts in joinery work.
  
• Fret Saw
  A fine-bladed saw used to cut delicate curves and intricate shapes in thin wood.
  
• Utility Knife
  A small, sharp knife used to cut, trim, or score wood, cardboard, or other materials.
  
• Dust Mask
  A face covering that protects from inhaling wood dust while cutting or sanding.
  
• Safety Goggles
  Clear, protective glasses worn to keep eyes safe from dust, wood chips, or flying particles.
  
• Ear Protectors
  Cushioned covers worn over ears to protect hearing from loud tools and machines.
  
• Apron
  A cloth or leather garment worn by carpenters to protect clothes and hold small tools.
  
• Tool Belt
  A waist-worn belt with pockets used to carry and organize tools while working.
  
• Wood Rasp
  A coarse tool similar to a file, used to roughly shape or smooth wood surfaces.
  
• Carving Knife
  A small, sharp knife used to carve fine details and shapes in wood.
  

List Of Carpenter Tools And Pictures

80 Carpentry Hand Tools

• Mortise Chisel
• Allen wrench
• Glue spreader
• Combination square
• Angle finder
• Depth gauge
• Edge trimmer
• Plungerouter
• Corner clamp
• Belt sander
• Orbital sander
• Disc sander
• Cordless drill
• Drill press
• Plumb bob
• Splitting wedge
• Work light
• Carpenter pencil
• Measuring tape
• Lag screw

Different Types of Tools Names in English with Pictures

• Mortise Chisel
  A strong chisel made to cut deep square holes (mortises) in wood for joints.
  
• Allen Wrench
  A small, L-shaped tool used to turn screws or bolts with hex-shaped holes.
  
• Glue Spreader
  A tool used to apply wood glue evenly on surfaces before joining them.
  
• Combination Square
  A multi-use tool for marking 90° and 45° angles and measuring short distances.
  
• Angle Finder
  A tool that measures angles, helpful when cutting wood at exact degrees.
  
• Depth Gauge
  A tool used to measure how deep a hole or cut is in wood.
  
• Edge Trimmer
  A tool that trims the edges of laminate or wood for a clean, even finish.
  
• Plunge Router
  A router that allows you to start cutting in the middle of the wood by lowering the bit straight down.
  
• Corner Clamp
  A clamp that holds two wood pieces at a right angle (90°) while gluing or screwing.
  
• Belt Sander
  A power tool with a moving sanding belt used to smooth or shape large flat surfaces.
  
• Orbital Sander
  A sander that moves in small circles, used for fine, smooth sanding work.
  
• Disc Sander
  A machine with a round spinning disc used to shape and smooth wood edges.
  
• Cordless Drill
  A battery-powered drill used to make holes or drive screws without needing a power cord.
  
• Drill Press
  A stationary machine that drills very straight and accurate holes into wood.
  
• Plumb Bob
  A pointed weight on a string used to check if something is perfectly vertical (straight down).
  
• Splitting Wedge
  A thick metal wedge driven into wood to split large logs apart.
  
• Work Light
  A bright portable light used to clearly see while working in dim or shadowed areas.
  
• Carpenter Pencil
  A thick pencil that marks wood clearly and doesn’t break easily while working.
  
• Measuring Tape
  A flexible metal strip marked with measurements, used for checking lengths or widths.
  
• Lag Screw
  A heavy-duty screw used to hold large pieces of wood together, often in framing or outdoor work.
  

Different Types of Tools Names in English with Pictures